Cabinetry paneling is used on the sides below the glass panels and on the doors accessing the lower section of the ClimaCab. In addition, if drawers are included, the drawer fronts would come standard with a small panel. The function of the panel is to allow a natural space for wood to move. The framework around the panel has a mortise on the interior edge. The panel is fashioned with a tenon around the perimeter, which fits into the mortise. We offer two types of panels - Mission or Raised.

A Mission Panel is a simpler, contemporary design used predominantly in modern style cabinetry. It also has a center panel and a flat frame overlay around the edge. The mission panel features straight lines and there is no decorative carving or raising in either the panel or the overlay. The center panel itself is completely flat, like a slab cabinet door, and the overlay around the edge is very sleek and simplistic looking. It's definitely a "less is more" design that is timeless and fits well with many interior spaces.

A Raised Panel design is a more formal design, used predominantly in traditional style cabinetry. In a raised panel, the cabinet is made up of a center panel and an outer rim or overlay. The center panel is carved on the edges which yields a raised center. The edges slope backward to the edges with a variety of profiles based on the cutter heads used. The entire effect is to make the cabinet door look as though it was carved out of a single, large plank, and it’s often subtly decorative in style. In addition to the panel appearance, selecting this option includes a Raised Panel Frame Edge Profile around the panel and the glass.

Replace the standard wood panel with glass to showcase certain items stored in the lower section, such as books, amplifiers, and effects pedals. We have the option to install UV Blocking/Safety Glass as well as interior LED lighting. Pricing varies based on ClimaCab size and whether we integrate the glass and lighting.

In most situations, the standard 17" high lower section must be expanded to accommodate the height of the amplifier on the pull out shelf. The shelf plus the hardware consumes 2 1/2" at the floor of the lower section and the face framing consumes another 4". A safe rule of thumb when estimating height required is to measure the amplifier resting on the ground to the top of the handle in its highest position and add 8". This will give a clearance of approximately 1 1/2" from the top of the handle to the upper face frame and account for any inaccuracies when measuring.

The table below will assist in determining height requirements to store your amplifier in the lower section of the ClimaCab.

• $375 per pull out shelf

• One time fee of $350 to expand lower section to 22 1/2" or $500 expanded more than 22 1/2" for most wood species. Exotic woods may incur additional cost based on board footage price, please inquire.

• $175/fixed shelf
• $225/adjustable shelf

• Pull out shelf - $325; Pull out tray - $375

• One time fee of $350 to expand lower section to 22 1/2" or $500 expanded more than 22 1/2" for most wood species. Exotic woods may incur additional cost based on board footage price

Hardware

• Blum undermount soft close slides, with full extension from the lower section

Construction

• All drawers are constructed with half-blind dovetail with 5/8" hardwood drawer box and 1/2" plywood bottom

Size and Quantity

• Drawer quantity depends on the width of the ClimaCab

Customizable

• Depth
• Internal dividers
• Split level

• $375/drawer

• Dividers - +$150/drawer

• Split level - +$175/drawer

Most of the time when lower section storage solutions are used, the height of the lower section must increase. For a low profile lower section, there are two options listed below. We are currently developing the first ClimaCabs without a lower section and will add to the photography when those are completed

• 10 1/2" Lower Section: We can utilize our low profile lower section to reduce the overall height. In situations where the humidification unit is used, the minimum height is 10 1/2". Compared to the standard lower section height of 17", this will reduce the overall height from 72 1/8" to 65 5/8".

• No Lower Section: In situations where height restrictions exist, we can completely eliminate the lower section. This is most likely applicable for rooms with sloped ceilings. When we remove the lower section, there are two options for humidity control. First, we can create a hardwood box which would be placed in the center of the upper section on the floor. Second, the ClimaCab can be humidified by only using the Boveda Two Way Humidity packets.  

Low Profile: same cost as standard lower section (17" height)

No Lower Section: -$250

Boveda Only Humidification / Eliminate Acoustic Remedy Humidity Control System: -$250

Addition of Internal Box to House Acoustic Remedy Humidity Control System (only applicalbe to No Lower Section Option): +$200

$550

We can implement other stain brands as long as they are compatible with our oil based catalyzed lacquer. This is very important because water based stains will cause issues with the lacquer topcoat application. Oftentimes we will recommend getting in the same color family as the stain you are trying to match. The reason is because trying to match perfectly is difficult due to natural aging, patina, and mellowing of certain wood species. Every situation is unique, so if this option interests you, please reach out for advice, recommendations, and options.

Sometimes the tinted lacquer process is not possible and in those circumstances we can apply actual paint. This process is done at a different finishing shop due to the specialty equipment required for a quality finish. We can implement other paint brands during this process and can match existing furniture, cabinetry, and trim provided we receive information regarding the brand, formula, paint type, sheen, primer requirements, and more.

Since this is such a customized approach, we will coordinate all necessary details and communicate with the finishing shop to ensure the final result is perfect. Pricing for this option is determined by many factors, so we will provide those details as the project progresses.

$600

This option may be desirable for those who do not want external cabinet pulls and want a more sleek, streamlined appearance.

The coved finger pull is a routed out section of the backside of the door frame and is an option for all sizes of ClimaCabs. For the ClimaCab Micro and Petite, which have one door, we can install in the center of the door frame on the upper and lower section. For the ClimaCab Petite+ and larger, which have two doors, we must route out the top of the door frames for the upper and lower section. This is required because the doors meet in the center with about a 1/4" gap and with the coved finger pull centered on the frames, it would be difficult to access and use.

We can install custom hardware for a $50 fee per ClimaCab. Our recommendation of proper size is that the lower section pulls should be approximately 2/3 the size of the upper section pulls. We typically use upper section pulls that are approximately 8" - 9" long and lower section that are 5 1/2" - 6" long.

We do not recommend putting knobs on the upper section; however, they can work appropriately on the lower section doors.

In order to keep this process simplfiied, we request that our customers purchase the hardware and ship to us. We will coordinate with the build team to ensure they are utilized and installed in the proper locations.

$300

$700